Official Luthiers Forum!

Owned and operated by Lance Kragenbrink
It is currently Thu Aug 14, 2025 9:34 am


All times are UTC - 5 hours


Forum rules


Be nice, no cussin and enjoy!




Post new topic Reply to topic  [ 31 posts ]  Go to page 1, 2  Next
Author Message
PostPosted: Mon Jun 08, 2015 1:41 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4820
I'm trying to thickness a highly figured set of koa sides with my Performax 10-20, and I'm getting burn with slow and fast conveyor speeds. Do any of you have tips?

I'm taking a forced break from it now after my conveyor belt broke. Probably a good thing. I'll have a go at it with a hand plane in a bit.


Sent from my iPhone using Tapatalk


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 1:55 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7474
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
On my 10-20 that usually means I'm trying to take of too much. I generally turn the depth-setting crank on top of the gantry only 1/8 to 1/4 turn for each pass and keep the conveyor at fastest speed.

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 2:01 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4820
Thanks, Steve. I'm only turning an eighth of a turn at most.

I remember years ago that Hesh was having a similar issue, but I couldn't find the thread.


Sent from my iPhone using Tapatalk


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 2:08 pm 
Offline
Contributing Member
Contributing Member

Joined: Sun Jan 27, 2008 4:10 pm
Posts: 2764
First name: Tom
Last Name: West
State: Nova Scotia
Country: Canada
Focus: Build
Status: Amateur
Too fine a grit........???
Tom

_________________
A person who has never made a mistake has never made anything!!!


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 2:09 pm 
Offline
Cocobolo
Cocobolo

Joined: Tue Feb 17, 2015 6:03 pm
Posts: 165
First name: Glenn
Last Name: Aycock
City: El Lago
State: Texas
Zip/Postal Code: 77586
Country: United States
Focus: Build
Status: Amateur
I have similar problems with mesquite. I typically use 36 or 60 grit for very hard/dense woods until very near desired thickness. Also, I run them through at 15-20 degree angle (on 16/32), but obviously you wouldn't want do do that for finishing passes.


Sent from my iPhone using Tapatalk


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 2:49 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood

Joined: Wed Feb 20, 2008 7:15 pm
Posts: 7553
First name: Ed
Last Name: Bond
City: Nanaimo
Country: Canada
Focus: Build
Status: Professional
I've found this to happen with maple as well. I found that running the conveyor at top speed and taking very, very light passes makes it turn out ok. Light like .001-.002 light. Takes forever but gets it done...


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 3:19 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Aug 23, 2010 11:42 pm
Posts: 1715
First name: John
Last Name: Parchem
City: Seattle
State: Wa
Zip/Postal Code: 98177
Country: USA
Focus: Build
Status: Amateur
I was going to suggest running it through at a diagonal, for some reason it really helps, but I am not sure you can on the 10-20. I do agree with the light passes I think an 1/8th every pass is too much. Adjust then run it through a few times adjust again. It does not sand all the way with one pass. If you adjust every pass you might be getting ahead of the papers ability to remove the wood.

_________________
http://www.Harvestmoonguitars.com


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 3:27 pm 
Offline
Koa
Koa

Joined: Sat May 19, 2007 11:03 am
Posts: 1737
Location: Litchfield MI
Focus: Build
Status: Professional
80 grit Zirconia, we get ours from Klingspor -- the grit is really sharp and stays that way for a long time. We make no effort to do finish sanding with our drum sanders -- after all they are "thickness sanders." 120g on a Random Orbit for preliminary smoothing.

_________________
Ken Cierp

http://www.kennethmichaelguitars.com/



These users thanked the author kencierp for the post: Glenn_Aycock (Mon Jun 08, 2015 7:07 pm)
Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 3:34 pm 
Offline
Koa
Koa

Joined: Fri Feb 16, 2007 12:14 pm
Posts: 1066
First name: Heath
Last Name: Blair
City: Visalia
State: California
Country: USA
Focus: Build
Status: Amateur
What grit are you using? What kind of dust collection? I've found that a large amount of airflow via a good size dust collector does a great job at keeping things cool.

_________________
sweat the small stuff.


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 3:41 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7474
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
Grit was my next thought as well. I use only 80 grit on my 10-20. I have no problem with Koa. Maybe there is something going on mechanically?

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 3:55 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4820
Thanks for all the input, guys. I run 100 grit. I'll order a pack of 80, and I'll take multiple passes before adjusting the drum.

Do any of you ever have issues with the paper snapping apart when you turn on the drum? I lost two brand new rolls to it today.


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 3:59 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7474
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
James Orr wrote:
...
Do any of you ever have issues with the paper snapping apart when you turn on the drum? I lost two brand new rolls to it today.


I've never had that problem. I've had it drag on the inboard side when I get down to around 0.050" (or in that neighborhood) but not had it actually snap apart.

_________________
Steve Smith
"Music is what feelings sound like"


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 4:29 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Nov 12, 2014 10:02 am
Posts: 513
First name: Daniel
Last Name: Petrzelka
State: Washington
Country: United States
Focus: Build
I had some light browning/burning with my 10-20 when trying to thin figured maple with 80 grit Performax Paper.

I need to order some of the Aluminum Zirconia 80 Grit that Ken mentioned ( http://www.woodworkingshop.com/product/pe40280/#.VXYH81xViko ), but here is how I made it work:

I did super light passes with 36 grit, feed on high speed. It seemed at lower speeds I'd get more heat build up. 2-3 passes between each thickness adjustment. I ran the pieces as much on the diagonal as I could. With these being long sides is was only a slight angle but helped. With three passes I'd to a >90 degree, <90 degree and then straight through.

I then only did some last finishing passes with the 80 grit - multiple passes at angles and straight through without adjusting the drum. Finished up with 120, 180 and 220 with the random orbital.



These users thanked the author dpetrzelka for the post: James Orr (Mon Jun 08, 2015 7:56 pm)
Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 7:11 pm 
Offline
Cocobolo
Cocobolo

Joined: Tue Feb 17, 2015 6:03 pm
Posts: 165
First name: Glenn
Last Name: Aycock
City: El Lago
State: Texas
Zip/Postal Code: 77586
Country: United States
Focus: Build
Status: Amateur
johnparchem wrote:
I was going to suggest running it through at a diagonal, for some reason it really helps, but I am not sure you can on the 10-20. I do agree with the light passes I think an 1/8th every pass is too much. Adjust then run it through a few times adjust again. It does not sand all the way with one pass. If you adjust every pass you might be getting ahead of the papers ability to remove the wood.

That's 1/8th of a turn, not inch. I can't remember what the thread pitch is, but that isn't much.


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 7:20 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4820
1/4 turn is supposed to be 1/64", or .015".

It's an interesting conundrum that I haven't had with any other woods. I've put rosewoods, tiger myrtle, mahoganies, and the usual crop of soft top woods through it without issue, but this koa is really taking the heat.

I ordered some 80 grit paper and a new conveyor belt, so we'll see how it goes. I'm going to have a go at it with my #5 1/2 tomorrow, but I'm concerned about the blade angle being too shallow for the figure. Thankfully the sides are pretty thick, so I won't have any permanent issues if I get tear out.


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 7:42 pm 
Offline
Cocobolo
Cocobolo

Joined: Mon Dec 15, 2014 1:35 am
Posts: 154
First name: Alan
Last Name: Jones
City: Cobble Hill
State: British Columbia
Country: Canada
Focus: Build
I don't run a 10 20......have a Grizzly, but the only time I have had trouble with burning I found that my paper was too loose on the drum. I tightened it properly and have had no problem since. Don't know if that could be your situation, but it was my solution.

_________________
Blue Ring Acoustics
blueringacoustics.ca


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 8:35 pm 
Offline
Koa
Koa
User avatar

Joined: Mon Sep 05, 2011 10:45 pm
Posts: 1484
First name: Trevor
Last Name: Gore
City: Sydney
Country: Australia
Focus: Build
Status: Professional
James Orr wrote:
I'm going to have a go at it with my #5 1/2 tomorrow, but I'm concerned about the blade angle being too shallow for the figure.

This one was thicknessed using only hand planes, but high angle (minimum 60 degrees). Try working across the grain to remove the bulk if you only have a standard angle plane, then finish up in line when you get your 10-20 back together.

Attachment:
Front_1_s.jpg


You do not have the required permissions to view the files attached to this post.

_________________
Trevor Gore, Luthier. Australian hand made acoustic guitars, classical guitars; custom guitar design and build; guitar design instruction.

http://www.goreguitars.com.au


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 9:37 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 20, 2008 9:12 pm
Posts: 6994
First name: Mike
Last Name: O'Melia
City: Huntsville
State: Alabama
Focus: Build
Status: Semi-pro
Klingspor blue, 80 grit, fast, light, diagonal passes to keep drum contact point cool. Even a 10/20 can do some diagonal. For me, things got way better when I started using that blue paper. You could even go coarser. Just remember you will have to go to a finer grit before final thickness


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 10:32 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Mon Aug 23, 2010 11:42 pm
Posts: 1715
First name: John
Last Name: Parchem
City: Seattle
State: Wa
Zip/Postal Code: 98177
Country: USA
Focus: Build
Status: Amateur
Glenn_Aycock wrote:
johnparchem wrote:
I was going to suggest running it through at a diagonal, for some reason it really helps, but I am not sure you can on the 10-20. I do agree with the light passes I think an 1/8th every pass is too much. Adjust then run it through a few times adjust again. It does not sand all the way with one pass. If you adjust every pass you might be getting ahead of the papers ability to remove the wood.

That's 1/8th of a turn, not inch. I can't remember what the thread pitch is, but that isn't much.


Sorry bad typing on my part, I get that you meant a 1/8th of a turn. I think a 1/4 turn is .3 mm. My point is that if you advance an 1/8 of a turn per pass you can out run the paper ability to sand. The paper may not be able to sand the 1/8th turn of depth in a single pass. So after several passes you may be trying to sand too much. For any on the hardwoods I advance an 1/8th turn and run multiple passes before I advance again.

_________________
http://www.Harvestmoonguitars.com


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 10:54 pm 
Offline
Cocobolo
Cocobolo

Joined: Tue Feb 17, 2015 6:03 pm
Posts: 165
First name: Glenn
Last Name: Aycock
City: El Lago
State: Texas
Zip/Postal Code: 77586
Country: United States
Focus: Build
Status: Amateur
johnparchem wrote:
Glenn_Aycock wrote:
johnparchem wrote:
I was going to suggest running it through at a diagonal, for some reason it really helps, but I am not sure you can on the 10-20. I do agree with the light passes I think an 1/8th every pass is too much. Adjust then run it through a few times adjust again. It does not sand all the way with one pass. If you adjust every pass you might be getting ahead of the papers ability to remove the wood.

That's 1/8th of a turn, not inch. I can't remember what the thread pitch is, but that isn't much.


Sorry bad typing on my part, I get that you meant a 1/8th of a turn. I think a 1/4 turn is .3 mm. My point is that if you advance an 1/8 of a turn per pass you can out run the paper ability to sand. The paper may not be able to sand the 1/8th turn of depth in a single pass. So after several passes you may be trying to sand too much. For any on the hardwoods I advance an 1/8th turn and run multiple passes before I advance again.

Agreed. I usually run it through every which way until it doesn't take any more material off, but I also prefer coarse grit. It just seems to work better.


Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 11:10 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4820
Regarding the paper being loose around the drum, I get it as taught as I can to leave as little slack for the springs as possible. I also crease it to minimize the the bulge where it feeds through. There is usually just a bit left. What do you guys like to do?

I also like to angle material as much as I can to spread the work out.

Great thread, guys! Thanks for so much solid feedback.



These users thanked the author James Orr for the post: Glenn_Aycock (Tue Jun 09, 2015 6:35 am)
Top
 Profile  
 
PostPosted: Mon Jun 08, 2015 11:16 pm 
Offline
Brazilian Rosewood
Brazilian Rosewood
User avatar

Joined: Wed Feb 20, 2008 9:12 pm
Posts: 6994
First name: Mike
Last Name: O'Melia
City: Huntsville
State: Alabama
Focus: Build
Status: Semi-pro
You know, another thought is to use an elevated bed. I have several boards (flattened) with sandpaper on them. Maybe .5" to .7" thick. I don't like getting the drum super close to the conveyor. It may help with heat transfer. I don't know for sure. But I haven't had burn problems in a long time. I think with time you will develop a touch and technique where burning won't be an issue.


Top
 Profile  
 
PostPosted: Tue Jun 09, 2015 12:08 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Feb 15, 2006 7:37 am
Posts: 4820
That's the thing! In the seven years I've had it, burning has never been an issue! [headinwall] :shock: :D

I'm using double sides for the first time, so I'm sanding the sides quite a bit thinner than I'm used to. I got my rosewood down to .055 without any problems, but I really don't want to take chances with the koa considering how scarce and expensive it's become. The backing board might be a great idea.


Top
 Profile  
 
PostPosted: Tue Jun 09, 2015 2:37 am 
Offline
Cocobolo
Cocobolo

Joined: Mon Apr 14, 2008 3:20 am
Posts: 376
Location: Kapolei HI
First name: Aaron
Focus: Build
Status: Semi-pro
+1 on 80 grit, although, I'm lazy all the time and more often than not leave the Klingspor 120 on my 16/32. Key for me is extremely good dust collection, clean paper, dust collection, 1/8 turns run through twice each side diagonally, dust collection, thickness from both sides, and the bottom line is good dust collection.

Of course, starting with a nice resaw at about .110 to .100 for sides, and <.125 for plates means little time under the sander.


Top
 Profile  
 
PostPosted: Tue Jun 09, 2015 6:29 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Wed Oct 08, 2008 11:36 am
Posts: 7474
Location: Southeast US
City: Lenoir City
State: TN
Zip/Postal Code: 37772
Country: US
Focus: Repair
I just read two points that caught my eye. First is dust collection, my sander has about a 6 ft run to an Oneida system so dust collection is about as good as it gets. If you are clogging with sanding dust that might cause it to heat up.

Second is it sounds like you are working at around 0.050" which, IME, is where the sandpaper can start contacting the conveyor. Don't know how your height is set but I keep the inboard side about 0.005" lower than the outboard side. This makes sure I don't dig a groove in the middle of tops or backs. If you are set up the same then clearance on the inboard side may be too tight and you may be sanding the conveyor belt which could lead to heat and belt or sandpaper damage. Where is your sandpaper breaking at?

_________________
Steve Smith
"Music is what feelings sound like"



These users thanked the author SteveSmith for the post: Glenn_Aycock (Tue Jun 09, 2015 6:40 am)
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 31 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: Bing [Bot], doncaparker and 20 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group
phpBB customization services by 2by2host.com